Questions tagged [raid0]

The tag has no usage guidance.

1
vote
0answers
22 views

How to convert RedHat 7 Raid 0 system from UUID to device (sda/sdb)

I'm trying to create an image of an RHEL 7.6 Raid0 device. I've eliminated the UUIDs from grub.conf, but the target device is still failing on boot because it's looking for the UUIDs from the source ...
2
votes
1answer
393 views

Extending RAID0 with `mdadm --create --assume-clean`?

I had a 1-disk RAID0 array that I created with a view of adding more disks to it eventually, that was working normally. I created it with (approximately): $ mdadm --create /dev/md0 --raid-devices=1 --...
-1
votes
1answer
181 views

linux + tool that can identify RAID configuration [duplicate]

I am searching for a long time tool that can runs as CLI on linux machine and identify which RAID configuration is defined on the disk or disks ( according to the list from lsblk ) the reason for ...
2
votes
1answer
385 views

Is it possible to clone Linux software RAID 0 array with LVM on top to a single HDD?

I have 2 500GB HDD in 3 software RAID 0 arrays with LVM on top. Both disks are partitioned: -MBR partition table -256 MB Physical volume for RAID -4 GB Physical volume for RAID -remaining 496 ...
0
votes
1answer
2k views

'mdadm: RUN_ARRAY failed: Invalid argument' when creating RAID0

I'm trying to create a RAID0 from two identical hard disks but running into an error from mdadm when I try to create the array, mdadm: RUN_ARRAY failed: Invalid argument. Here's what I'm doing that ...
0
votes
1answer
950 views

fakeraid + UEFI + GPT - grub doesn't detect raid volume after debian install using dmraid

I have a post on the debian forums as well but it seems to have less traffic than here so I thought I'd try my luck here as well. I'm trying to install windows 10 and debian and possibly more ...
1
vote
0answers
930 views

Assistance with mdadm.conf syntax for reassembly of existing RAID0

I'm trying to recover a friends data from a Sony Vaio VGN-AW47GH Laptop. It has a pair of Toshiba MK5055GS 2.5" 500GB HDD combined (according to my reading) into a 1TB RAID0. The laptop is no longer ...
1
vote
1answer
333 views

mkswap complains that partition is misaligned (LVM on RAID-0)

I have a RAID-0 setup on two identical hard disks (same brand and model). The partition table is identical on both (I have cloned it). However, /dev/md0 occupies only part of the disks, because I had ...
1
vote
1answer
748 views

raid5 array reassembles as raid0

I found simmilar problem here: Missing mdadm raid5 array reassembles as raid0 after powerout, but mine is a bit different. Here too my raid5 reassembles as raid0, but i don't see any of my devices ...
3
votes
1answer
100 views

BTRFS has become unmanageable

I'm struggling with a btrfs RAID0 filesystem. It's expanded on 4 disks but i need to remove one of those disks. This is the current status of the filesystem: [root@osgiliath detlev]# btrfs fi show /...
2
votes
1answer
1k views

'PARTUUID' in '/etc/fstab' and (hardware) RAID0 don't play well together, do they?

Fresh Arch Linux install on (hardware) RAID0 under 64-bit UEFI system with GPT partitions. Had to add MODULES="ext4 dm_mod raid0" HOOKS="base udev autodetect modconf block mdadm_udev filesystems ...
1
vote
1answer
86 views

Unable to mount RAID 0 drive

When I run the following command: sudo dmraid -ay I'm getting this error: ERROR: opening "/dev/mapper/isw_cigjeghbef_RAID 0" And, after attempting to open the drive in the file explorer, I get ...
2
votes
1answer
2k views

Unable to boot after installing grub for new Arch Linux Install on Acer S7

I have followed the instructions on the Arch Linux beginner's guide to do a dual boot on an Acer S7-392. I only did not do the initramfs part and I did not create the partitions at the install since I ...
1
vote
2answers
6k views

Use MegaCLI to add a new hard disk to existing RAID0 in Linux

There are two hard disks on my machine, but after installing the operating system, it uses only one hard disk to build RAID0. After installing MegaCLI, I used: MegaCli64 -pdlist -aALL to display ...
0
votes
1answer
436 views

XFS on Volume Group or Mdadm Raid 0

Im starting to use XFS because I want to create a highly parallel disk array and experimenting on just 2 drives for now. I had thought that if I used a logical volume group to join two physical ...
1
vote
1answer
204 views

Clone installed system by using the hardware RAID 0+1 synchronization

Alright, following setup: 2 identical machines (DELL Power Edge T320) with a hardware raid. one machine is running for a while now, one machine hasn't even been set up at all The running machine has ...
2
votes
1answer
4k views

Adding badblocks on mounted partition

I tried to move some files to my NAS (ShareCenter DNS-320), but something shows up, when using file managers: Input/Output error or when using rsync on mounted cifs/smb share rsync: close failed on ...
2
votes
1answer
3k views

How do I set up RAID0 using extra two drives? [closed]

I have been looking around for a suitable tutorial to help me set up a RAID0 across two (or more) drives, but not moving the actual installation of Linux Mint onto that RAID setup. A coworker had ...