Possible Duplicate:
Find filesystem of a partition from a script
How to show the filesystem type via the terminal?

I'm looking for a command that yields the filesystem type as mount would use/detect it, without actually mounting it. It should also work e.g. for LUKS encrypted devices (where file -s yields "LUKS encrypted file" instead of "crypto_LUKS"). Surely there is a more convenient way than parsing fsck -N /dev/whatever's output (which may use stderr depending on the existence of a corresponding fsck.TYPE)?

  • 5
    @StephaneChazelas that's not a duplicate, df reads mount table and doesn't show about unmounted ones.
    – daisy
    Nov 2, 2012 at 2:26

1 Answer 1


There are multiple ways to get this information. Most of them require you to parse the output of another command.

  • Run # fdisk /dev/sdX -l to get a basic idea of the filesystem structure. The output is something like this:

    Disk /dev/sda: 320.1 GB, 320072933376 bytes, 625142448 sectors
    Units = sectors of 1 * 512 = 512 bytes
    Sector size (logical/physical): 512 bytes / 512 bytes
    I/O size (minimum/optimal): 512 bytes / 512 bytes
    Disk identifier: 0x9f7685a8
       Device Boot      Start         End      Blocks   Id  System
    /dev/sda1              63      289169      144553+  83  Linux
    /dev/sda2          289170   459121634   229416232+  83  Linux
    /dev/sda3       459121635   461129759     1004062+  82  Linux swap / Solaris
    /dev/sda4   *   461129760   625142447    82006344    7  HPFS/NTFS/exFAT

    But this will only tell you the partition type.

  • You could also use # blkid to get the following output:

    /dev/sda1: LABEL="boot" UUID="aa84c5a8-6408-4952-b577-578f2a67af86" TYPE="ext2" 
    /dev/sda2: LABEL="root" UUID="a430e0ef-fd35-432f-8b9a-75a49b89ad8a" TYPE="ext4" 
    /dev/sda3: LABEL="swap" UUID="e388806a-dc27-4f4e-a136-3d1ff4e53962" TYPE="swap" 
    /dev/sda4: UUID="088E027A8E026114" TYPE="ntfs" 
  • Also, for a well formatted output, you could run # parted /dev/sdX -l for the following output:

    Model: ATA WDC WD3200BEVT-7 (scsi)
    Disk /dev/sda: 320GB
    Sector size (logical/physical): 512B/512B
    Partition Table: msdos
    Disk Flags: 
    Number  Start   End    Size    Type     File system     Flags
     1      32.3kB  148MB  148MB   primary  ext2
     2      148MB   235GB  235GB   primary  ext4
     3      235GB   236GB  1028MB  primary  linux-swap(v1)
     4      236GB   320GB  84.0GB  primary  ntfs            boot
  • $ df -T. This is another command that does not require super user privileges to execute. However, this will report for every mount point

    Filesystem     Type     1K-blocks     Used Available Use% Mounted on
    rootfs         rootfs   225815276 99381340 114963128  47% /
    dev            devtmpfs   1538396        0   1538396   0% /dev
    run            tmpfs      1541260      416   1540844   1% /run
    /dev/sda2      ext4     225815276 99381340 114963128  47% /
    tmpfs          tmpfs      1541260      360   1540900   1% /dev/shm
    tmpfs          tmpfs      1541260        0   1541260   0% /sys/fs/cgroup
    tmpfs          tmpfs      1541260      900   1540360   1% /tmp
    /dev/sda1      ext2        139985    30386    102372  23% /boot
    /dev/sda4      fuseblk   82006340 79676036   2330304  98% /mnt

Another command that can come handy is # file -sL /dev/sdXY. This has one downside in that it does not work with the full block device. Requires the exact device to be passed. The output is quite neat though:

/dev/sda1: Linux rev 1.0 ext2 filesystem data (mounted or unclean), UUID=aa84c5a8-6408-4952-b577-578f2a67af86, volume name "boot"

All of these will always be output to stdout. You can parse them in a script if required.

  • 1
    (eval $(blkid $DEV | awk ' { print $3 } '); echo $TYPE) will do, thanks! (The outer parantheses are only necessary if TYPE is already used elsewhere and shall not be changed) Nov 1, 2012 at 16:34
  • 1
    df -T will claim tmpfs for any loopdevice it seems, and fdisk -l doesn't appear to list a type when applied to a partition itself, while parted ignores the device for me and file -s yields the wrong format for a luks encrypted device. But blkid works perfectly, even for a loop device or the image file itself Nov 1, 2012 at 16:42
  • That behavior is expected out of df -T and fdisk -l. However, I don't understand how parted ignores the complete block device.
    – darnir
    Nov 1, 2012 at 16:48
  • 4
    That may be due to the linux I tried to run this on (it's a custom distro on a Buffalo LinkStation NAS device) Btw, even better solution: blkid -o value -s TYPE $DEV Nov 2, 2012 at 7:02
  • 12
    #lsblk -f would also help at least it returns every mounted or unmount block devices. Mar 26, 2015 at 10:38

Not the answer you're looking for? Browse other questions tagged or ask your own question.