7

Hy there, I am having problem in connecting my raspberry pi to a wifi dongle. I have followed a lot of tutorials from internet but no success so far.

My WIFI dongle can scan the networks but it's not connecting to any network.Here is what my configuration file looks like

ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev 
country=GB 
update_config=1


network={
    ssid="noname"
    #psk="zong4gisbest"
    psk=ead5b0b7e82e1a68f01e9a17a2a7719ec24575c89bb5b5805e4ae49c80daa983 }

Here are the results of my commands on Raspbian

iwconfig

wlan0     unassociated  Nickname:"<WIFI@REALTEK>"
          Mode:Auto  Frequency=2.412 GHz  Access Point: Not-Associated
          Sensitivity:0/0
          Retry:off   RTS thr:off   Fragment thr:off
          Power Management:off
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

eth0      no wireless extensions.

lo        no wireless extensions.

lsusb

Bus 001 Device 004: ID 0bda:0179 Realtek Semiconductor Corp. RTL8188ETV 
Wireless LAN 802.11n Network Adapter
Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp. SMSC9512/9514   
Fast Ethernet Adapter 
Bus 001 Device 002: ID 0424:9514 Standard Microsystems Corp. SMC9514 Hub   
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

Can you please help me resolving the issue?

thanks

10

Edit your wpa_supplicant.conf , change the following lines:

network={
    ssid "noname"
    psk"zong4gisbest"

to:

network={
    ssid="noname"
    #psk="zong4gisbest"
    psk=ead5b0b7e82e1a68f01e9a17a2a7719ec24575c89bb5b5805e4ae49c80daa983
}

save then run

wpa_supplicant -iwlan0 -D wext -c/etc/wpa_supplicant/wpa_supplicant.conf -B
dhclient wlan0

The error:

nl80211: Driver does not support authentication/association or connect commands

mean that the standard nl80211 doesn't support your device , you should use the old driver wext.

To correctly set up your wpa_supplicant.conf , it is better to use the wpa_passphrase command:

wpa_passphrase YOUR-SSID YOUR-PASSWORD >> /etc/wpa_supplicant/wpa_supplicant.conf

To automatically connect to your AP after restart edit the wlan0 interface on your /etc/network/interfaces as follow:

allow-hotplug wlan0
iface wlan0 inet dhcp
    wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf
| improve this answer | |
  • Tried using wpa_passphrase YOUR-SSID YOUR-PASSWORD >> /etc/wpa_supplicant/wpa_supplicant.conf But here is the error imgur.com/a/TudGH – Usama Saeed Oct 24 '17 at 10:27
  • after saving, when i tried>>wpa_supplicant -iwlan0 -c/etc/wpa_supplicant/wpa_supplicant.conf -B I see this error now imgur.com/a/wrDrh – Usama Saeed Oct 24 '17 at 10:30
  • 1
    What's wext? I am sorry, i am kinda new here! – Usama Saeed Oct 24 '17 at 10:41
  • 1
    Hey bro, it just worked. I thought, you asked me to use two different commands 1>>wpa_supplicant -iwlan0 -D wext -c/etc/wpa_supplicant/wpa_supplicant.conf -B 2>>dhclient wlan0 I didn't know that it's a single command. Now it worked great. I am doing ssh using wifi now. thanks bro – Usama Saeed Oct 24 '17 at 12:30
  • 1
    However each time i restart the pi, i have to do that command to enable wifi. is there any hack which can do the job? thanks again – Usama Saeed Oct 24 '17 at 12:42

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.