5

When re-partitioning the USB drive on CentOS 6.x getting following error.

Disk /dev/sdb: 31.5 GB, 31466323968 bytes
255 heads, 63 sectors/track, 3825 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x0e693bd9

   Device Boot      Start         End      Blocks   Id  System
/dev/sdb1   *           1        3826    30727808    c  W95 FAT32 (LBA)
[root@csc ~]# fdisk /dev/sdb

WARNING: DOS-compatible mode is deprecated. It's strongly recommended to
         switch off the mode (command 'c') and change display units to
         sectors (command 'u').

Command (m for help): d
Selected partition 1

Command (m for help): 1
1: unknown command
Command action
   a   toggle a bootable flag
   b   edit bsd disklabel
   c   toggle the dos compatibility flag
   d   delete a partition
   l   list known partition types
   m   print this menu
   n   add a new partition
   o   create a new empty DOS partition table
   p   print the partition table
   q   quit without saving changes
   s   create a new empty Sun disklabel
   t   change a partition's system id
   u   change display/entry units
   v   verify the partition table
   w   write table to disk and exit
   x   extra functionality (experts only)

Command (m for help): d   
No partition is defined yet!

Command (m for help): n
Command action
   e   extended
   p   primary partition (1-4)
p
Partition number (1-4): 1
First cylinder (1-3825, default 1): 
Using default value 1
Last cylinder, +cylinders or +size{K,M,G} (1-3825, default 3825): 
Using default value 3825

Command (m for help): 
Command (m for help):  
Command (m for help): t
Selected partition 1
Hex code (type L to list codes): 86
Changed system type of partition 1 to 86 (NTFS volume set)

Command (m for help): w
The partition table has been altered!

Calling ioctl() to re-read partition table.

WARNING: Re-reading the partition table failed with error 16: Device or resource busy.
The kernel still uses the old table. The new table will be used at
the next reboot or after you run partprobe(8) or kpartx(8)
Syncing disks.
12

Looks like this device is mounted. Run umount /dev/sdb1 and try again.

  • Concur. If the device wasn't mounted beforehand, please update the question to reflect that. If it was, try this and update the question with the results if it didn't work. – Shadur Jan 8 '18 at 9:06
  • @Shadur I'm getting the error in a similar situation and the device is not mounted. – jhfrontz May 29 at 22:32
0

try o command at fdisk, it will building a new DOS disklabel.

or try partprobe or kpartx -a if you have this command.

0

try command: sudo resize2fs /dev/mmcblk0p2

  • what does it do? – Pierre.Vriens Jan 8 '18 at 8:53
  • 2
    Please elaborate why you think this will help, because unless I'm missing something important the only thing this will do is potentially inflict further damage on the filesystem when it's already in an unknown state. – Shadur Jan 8 '18 at 9:05
0

Assuming that you're getting this as a result of automating (e.g., using expect) the fdisk operation (and that the partition isn't actually mounted), try adding a few seconds of delay after modifying the partition and before writing the partition able.

I got the same error when I was trying to automate a call to fdisk on Centos 7.6 a la:

# (echo "d"; echo "";
        echo "n"; echo ""; echo 3; echo 2001954; echo "";
        echo "w") | fdisk /dev/sdb
Welcome to fdisk (util-linux 2.23.2).

Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.


Command (m for help): Partition number (1-3, default 3): Partition 3 is deleted

Command (m for help): Partition type:
   p   primary (2 primary, 0 extended, 2 free)
   e   extended
Select (default p): Using default response p
Partition number (3,4, default 3): First sector (2001954-31116287, default 2002944): Last sector, +sectors or +size{K,M,G} (2001954-31116287, default 31116287): Using default value 31116287
Partition 3 of type Linux and of size 13.9 GiB is set

Command (m for help): The partition table has been altered!

Calling ioctl() to re-read partition table.

WARNING: Re-reading the partition table failed with error 16: Device or resource busy.
The kernel still uses the old table. The new table will be used at
the next reboot or after you run partprobe(8) or kpartx(8)
Syncing disks.


My suspicion was that my piped-in command stream was surfacing a timing issue in fdisk (that wouldn't be triggered by slower/manual input) so I started sprinkling sleep commands to delay various inputs until the error went away. The problem in my case was that the w was happening too soon after the new partition was defined.

A sleep 5 before the w results in consistent success:

# (echo "d"; echo "";
        echo "n"; echo ""; echo 3; echo 2001954; echo "";
        sleep 5; echo "w") | fdisk /dev/sdb
-1

May be you tried like "sudo fdisk /dev/sdc1"this

Solution:if you want to create a partition of /dev/sdc then command should be: "sudo fdisk /dev/sdc" not as "sudo fdisk /dev/sdc1".

  • Where's sdc in this situation, though? – Jeff Schaller Nov 21 '18 at 15:19
-1

I face this issue as i mounted 1 partition and then try to create another partition. Umount initially created partition and then error gone.

protected by dr01 Jun 5 at 10:26

Thank you for your interest in this question. Because it has attracted low-quality or spam answers that had to be removed, posting an answer now requires 10 reputation on this site (the association bonus does not count).

Would you like to answer one of these unanswered questions instead?

Not the answer you're looking for? Browse other questions tagged or ask your own question.