Some applications simulate a virtual USB or CD Rom drive as if a USB drive is attached to the computer.

Is there any configuration or application that provides a virtual USB drive, not for the the operating system itself, but for other equipments which accept USB drive, through a USB port.

So I'll have a virtual hard disk (e.g. a *.vdi file) in the computer, which is connected, through a USB socket, as a USB drive to some other equipment (e.g. a cell phone or a laptop).


You would need to add a USB Device/Peripheral controller to the computer, as opposed to the USB Host Controller they tend to come with.

Something like this: https://www.maximintegrated.com/en/products/interface/controllers-expanders/MAX3420E.html

Unfortunately, you'd have to find a way to wire it onto your motherboard. Technically, it can be done. Practically, you'd have to redesign the motherboard to include it. You might be lucky enough to find an SPI or I2C bus exposed somewhere on your motherboard to allow you to add it, but they're usually wired directly into whatever they're being used for unless you're using a dev board or single-board computer with exposed GPIO and other ports such as a Raspberry Pi.

The other option would be a USB On-the-Go Controller. Motherboards designed for embedded and portable devices tend to have a USB OTG (On-the-go) contoller, which can function as either a Host or Device controller. For example, the aforementioned Raspberry Pi has an On-the-Go Controller, but on all models except the Pi Zero that gets rewired to a host port or an onboard USB hub denying the use of USB device functionality. The BeagleBone Black has an OTG port.

That's not all though - once you've got the hardware, you'd also need the software. Linux has some useful kernel USB Gadget drivers ("USB gadget" is another term for USB peripheral/device) such as g_serial and g_ethernet that allow you to plug your device into another computer and be visible as a serial or ethernet-over-USB device (there are others for exposing a device as mass storage, which allow you to use a file as a block device and expose the computer as a mass storage gadget). The BeagleBone Black tends to come with this enabled by default, so you can simply plug it into your PC over USB and see it as a networked device - and I believe it also appears as a mass storage device by using a composite driver (which allows it to appear as multiple USB device types over a single connection.) The Pi Zero can use these, but does not by default. For Windows or other OSes, you'd probably have to write that device driver yourself.

So, theoretically, you can do it. You can tear down your desktop PC, try and find an unused compatible bus on the motherboard somewhere (most likely some unused pins on a controller IC), or a way to extend an internal I2C or SPI bus, or something you can tear out and replace, and solder a USB OTG or device controller chip onto it. Then you can install Linux and use a gadget driver, or write your own for another OS. Practically, unless you're a top-notch electronics engineer, you're not going to be able to do it. At least, not until someone comes out with that elusive adapter with a device or OTG port on it that plugs into a USB port (theoretically, that could be done with a microcontroller such an Arduino wired to a pair of USB device controller ICs), and writes the drivers to run it.

  • 3
    great explanation, can you please update the answer if you (with your knowledge) see something new regards your sentence "until someone comes out with exclusive adapter...". There are laptops with usb-c in 2018, could they be a solution.? – Asain Kujovic Sep 10 '18 at 16:41
  • 2
    Update since 2016: the RPi4 supports USB OTG via its USB-C port. Previous RPi versions did not support this. Doesn't answer the question directly (RPi is not a PC adapter), but might help someone who's dissuaded by the above, which was correct at the time. – bjornruffians Jan 15 at 16:00

USB is dissymmetric: one side is a host, the other side is a peripheral device. You can't make a peripheral device act as a host or vice versa. It is possible for a USB port to be able to act as either side; this is called USB on-the-go and is present on some mobile phones and tablets. The ports are physically device-type ports, not host-type ports. I've never seen a PC with a device port. This requires electronics on the controller, it isn't enough to make a cable that fits on both ends.

So no, you won't be able to make a PC into a USB device.

If you want to use a computer as a USB storage device, you can use a mobile phone or tablet with a USB connection instead of using a PC.

  • Can you elaborate a bit more, how using a mobile phone could help me turning my PC into a USB storage device / host, that I could plug to another compter, TV or device? I think, I'm missing this point, though I think I have a fair knowledge about USB OTG. – trejder Mar 10 '15 at 8:15
  • @trejder As I wrote, I've never seen a PC with a device port (“PC” excluding x86 tablets). – Gilles 'SO- stop being evil' Mar 10 '15 at 8:19
  • Yes, but I'm refferring to your last sentence: "If you want to make a computer into a USB storage device, you can use a mobile phone or tablet with a USB connection". Maybe I'm missing something, but I understand it as "You can use mobile phone or tablet to turn computer into USB storage device". If so, then the question is: How? – trejder Mar 10 '15 at 8:23
  • 1
    @trejder Ah, “computer” in that sentence is not “PC”, it's “computer”. A phone/tablet is a different kind of computer from a PC. Is that what's troubling you? – Gilles 'SO- stop being evil' Mar 10 '15 at 8:27
  • 1
    @trejder No. Usually your best bet is to establish a network connection one way or another. You can use Firewire as a network connection between any two PCs with a Firewire port, but many PCs don't have one. Most PCs have an Ethernet port, you can connect two PCs with an Ethernet cable (very old PCs require a crossover cable but modern ones can take an ordinary cable). To make a PC serve as a storage device for a mobile device, you typically need to get the PC onto wifi somehow. – Gilles 'SO- stop being evil' Mar 10 '15 at 8:35

I do wish people would stop repeating the erroneous claim that all personal computers lack the hardware to act as a USB device/slave/gadget/whatever. I can prove this is not the case. My first example of this is that all Apple Mac computers with a USB-C port have the capability of going into a USB-C slave mode. This is called "Target Disk Mode", and it is documented here: https://support.apple.com/en-us/HT201462

This is a function of temporarily turning your $2000 laptop into a $200 USB-C drive. Why do this? So that one can repair the drive on a non-booting Mac for one. How does this work? It works because Apple used a USB-C chip in their computers that is capable of acting as a USB slave/device/whatever, and installed some firmware to allow this function. This chip is not unique to Apple computers, this is also used by a number of other computer manufacturers.

There's more evidence to back up that most every laptop with USB-C ports also have the hardware needed to act as a USB slave/device. Take a laptop that uses USB-C for power and charging, get a USB-C to USB-C, get another computer with a USB-C port that is running Windows. Now, connect the laptop to the Windows computer with the USB-C cable and check the Device Manager for new devices. If the laptop is drawing power from the Windows computer then you should see in the Device Manager the laptop show as a "USB billboard device" in the list of devices. This is the laptop acting as a USB device. It has to appear as a device to a USB Power Delivery capable host, such as a USB-C power brick, to draw more than 5 watts of power. There's other ways of checking this so adjust the process for your preferred operating system or whatever.

Why don't more operating system publishers use this capability to do more than just charge batteries in laptops? That's a good question. That's a question I've been looking to answer for a long time.

There are some people working on expanding the capability of Linux systems to act as USB devices. It works right now for a wide range of USB virtual devices but it's not trivial to setup. I'm hoping that someday soon this capability becomes better supported, and is expected by users to work simply, easily, and with the high performance we expect from USB 3.x devices.

The hardware is already there for computers to act as a USB device in most every computer with USB-C ports, we just need more people working on writing the software to make this something the average user (or even slightly above average user) can set-up and use.

  • I think you're forgetting that the question was asked in 2014, which as of your answer is six years ago – roaima Jun 20 '20 at 11:16
  • Yes, but... USB 3.0 supported host to host connections since 2009 so this was possible in 2014. There's documents from at least as far back as 2012 on how to set up USB-A to USB-A connections on USB 3.0 ports for Windows 7 and 8 kernel and driver debugging. This was also done in Linux at that time. Apple had USB Target Disk mode capable laptops in early 2015, about the same time as one reply and years before the 2017 reply claiming this is impossible. So, my comments would be not all that helpful in 2014, only true for new Apple hardware in 2015, but quite relevant by 2017. – MacGuffin Jun 20 '20 at 12:08
  • “There are some people working on expanding the capability of Linux systems to act as USB devices. It works right now for a wide range of USB virtual devices but it's not trivial to setup.” Hi. Can you be more specific in describing what needs to be set up in LineageOS (Android)? – beroal Feb 8 at 20:23

As explained in the answer by by Matt Thomson, it is not properly possible to make a physical USB port of a PC computer act as a USB slave device, as the USB slave controller is missing.

That means if we have an adapter board that can provide slave-mode USB (such as the Raspberry Pi Zero), we have to connect it to your host PC by a different channel, such as wired Ethernet. I have two different proposals what protocol you could run over that Ethernet connection:

(1) Expose the USB port over IP network.

Use software to expose the USB slave-mode port of the Raspberry Pi Zero as a virtual USB device to your PC. The USB/IP project provides this, by means of a driver that can transport USB over IP networks. Here is an example of using USB/IP to provide a simulated USB device to a computer – which would be your PC here.

What I don't know in this proposed solution is if the USB/IP software is already able to expose a USB slave port over IP network, or only a USB host port as normal.

But even if that works, you still have to set up or adapt device drivers on your PC in such a way that they (1) accept the incoming USB/IP connection as a USB connection, (2) provide USB slave-mode rather than USB host-mode, (3) simulate a USB mass storage device by serving the data from the assigned location (your .vdi file).

Overall, that's a complex way of doing it.

(2) Expose the file over IP network.

This is a much simpler way for how to utilize the Ethernet connection to the Raspberry Pi Zero: on the Raspberry Pi Zero, mount the data stored on your PC via a network file system. These files then appear logically as part of the Pi Zero's file system, and you can serve them with the Linux USB gadget driver to make the Raspberry Pi look like a USB mass storage device to connected devices.


You can consider using one of special "USB-USB bridged cables", sometimes called "USB networking cables". Like one mentioned in these articles:

They allow you to transfer files between two PCs. I've been using these kind of cables over ten years ago (in times of Windows XP) and in that times all such cables available to the market required a special driver and software. They let you transfer files only through special file commander, that shiped along with cable drivers on a installation disk and therefore did not allow one PC to act to another as pure USB external device.

I'm not sure, if anything has changed since then and if new solutions allow you only to transfer files using special software and -- if you can force one PC to act as an external device to another PC.


Technically this should be doable with http://www.bplus.com.tw/Adapter/PP3380-AB.html - PP3380-AB (USB3380-AB Evaluation Board) which appears to include a USB3.0 5gbps USB B port on a pci express card, and is built around a Linux USB Gadget supported PLX USB3380 chip. But it's not cheap (250$) and probably far from trivial (programmer not included...).

(Note: there's also http://www.bplus.com.tw/Adapter/USB3380EVB.html where a USB3380-AB EVK with ADP board gets you a microUSB port - but that's just a cable difference)

  • That requires use of a desktop system, or breakout box, with an open PCIe slot. Ever since the MacBook with USB-C in 2015 there's been a number of laptop computers with the same USB controller. This USB-C/USB-3 chip can go into device mode as demonstrated by the MacBook being capable of Target Disk Mode on it's single USB-C port ( en.wikipedia.org/wiki/Target_Disk_Mode ) Since this same USB controller chip is used in a large number of laptops there should be many to choose from to experiment with. It's possible that this same USB controller is used in some desktop systems as well. – MacGuffin Aug 9 '20 at 20:08
  • Sounds like that's the Intel® JHL6540 Thunderbolt™ 3 Controller (Alpine Ridge) or on 2018+ the newer Intel® JHL7540 Thunderbolt™ 3 Controller (Titan Ridge). I happen to have a Alpine Ridge (DSL6540) on my motherboard, but I can't figure out how to flip it into peripheral mode in Linux. – MaZe Aug 11 '20 at 1:32

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.