Virtual Private Network
8
votes
2answers
755 views
Openswan connecting to multiple right subnets not working
I'm trying to use Openswan (version 2.6.37) to connect an IPsec VPN from my local network to a remote site. Everything works fine when I just want to connect to a single subnet on the remote site. ...
6
votes
1answer
301 views
Load Balancer Solution with linux
I need a suggestion to realize a proper solution to this problem:
As you can see in the image above, I have 2 application servers that need to talk with and external third party provider over the ...
6
votes
2answers
515 views
Linux -> linux remote X login/desktop
What are the (best) solutions for remote desktop in linux? Ideally I'd like to be able to be able to log in to a remote X (KDE) session without even logging into my local machine. Maybe if I could ...
6
votes
3answers
219 views
How can I tunnel traffic for a NATted host to another server?
I have a device on my private network which I don't wish to allow to directly access the internet from my gateway. Instead, I want to tunnel that traffic from my gateway to another server (also mine) ...
5
votes
1answer
5k views
Use ssh with a specific network interface
I'm using openconnect to connect to vpn. After entering my credentials, I get this:
POST https://domain.name/...
Got CONNECT response: HTTP/1.1 200 OK
CSTP connected. DPD 30, Keepalive 30
Connected ...
4
votes
2answers
733 views
What is resolv.conf and why VPN client's hack it?
As stated in a previous question I want to connect to 2 VPN servers at the same time and for each connection specify the IPs of computers I want to reach with it.
One of this VPN connection is done ...
4
votes
3answers
617 views
Redirect traffic through vpn on an as needed basis
My problem is really simple yet it sounds complex, but I have zero to none experience with this.
I have set up a box using gentoo which has its own semi-static WAN-IP and acts as router for my LAN. I ...
4
votes
3answers
547 views
How to access a machine behind a restricted NAT gateway I don't manage?
I have a linux machine that I'd like to be able to access remotely for SSH, FTP, HTTP, and so forth. I signed up for Dynamic DNS with No-IP.com, but this isn't adequate because I am on a college ...
4
votes
1answer
628 views
Force VPN using IPtables?
I want to force the use of VPN using iptables, therefore while VPN is disabled no outgoing traffic shall be allowed (except maybe some DHCP stuff...). Now i guess I could just block everything not ...
4
votes
2answers
1k views
VPN with network manager (nm-applet) is not working
My university (TU Wien) offers a VPN in order to get an IP of the university network. The instruction on the university webpage says to install the packages network-manager-gnome, network-manager-vpnc ...
3
votes
2answers
2k views
Port forward to VPN Client?
I've run into a bit of a puzzle and haven't had much luck finding a solution. Right now I am (sadly) connected to the net via Verizon 3G. They filter all incoming traffic so it is impossible for me to ...
3
votes
2answers
236 views
Can't SSH via password to a Remote Server
I've successfully VPNed to my University server on a Fedora 17 Linux terminal.
$ sudo openconnect -u UNIVERSITY_USERNAMEID sslvpn.nameofuniversity.edu
[sudo] password for PCUSERNAME:
Attempting to ...
3
votes
1answer
2k views
Is route add … the best way of directing traffic through a vpn
I have set up a VPN on a remote ubuntu machine using pptp-linux and the instructions found here.
After set up no traffic seemed to be going through the VPN and the VPN network devices were not ...
3
votes
3answers
1k views
VPN on Fedora Linux?
I'm looking to install and setup a VPN on my Linux installation which is Fedora 14. At the moment the only one I know of is OpenVPN but I'm wondering if this the best option for Fedora or if Fedora ...
3
votes
2answers
517 views
Need help with routing
I have set up a Ubuntu server, that I want to use as a router for my local office.
The problem is, that I want to make 2 VPN connections, to remote branches, and then I want to route all traffic to ...
3
votes
1answer
644 views
Installing OpenVPN to replace Cisco VPN because Cisco will not work with the kernel I am on or downgrade instead?
I had difficulties installing Cisco5.0 VPN on my Ubuntu 10.04 LTS. I asked for assistance in this question: link to previous question. The answer is that this Cisco program will run on only older ...
3
votes
1answer
207 views
What's the best way to install a system-wide certificate from a website?
I want to use the Cisco Easy VPN to connect to the OpSource cloud machines. When I open the app, it directly shows a certificate error message, I suspect that the certificate is not trusted from their ...
3
votes
1answer
1k views
What is the best touch screen kiosk solution?
I'm a web developer and I'm looking for the best stripped-down linux experience that provides a full-screen experience for touch screens. I'll be looking for:
a robust experience that stops people ...
3
votes
0answers
274 views
Route VPN traffic through socks proxy
There is no way to set proxy on an unrooted Android, but there is an option to connect to VPN.
In my network VPN connection is not allowed! so I am looking for a way to run a local VPN server on my ...
3
votes
0answers
796 views
What is SSTP vpn server and how can I run one?
I've read a couple of L2TP and PPTP tutorials on the net and there are just dozens of "running PPTP/L2TP on Linux" guides available out there and I successfully made packages like open-swan or pptpd ...
3
votes
1answer
1k views
How do I configure OpenVPN as a Gateway client for Witopia?
I have the following setup:
Witopia SSL account
Synology 409 NAS (with OpenVPN and Apache etc)
PS3
Mac
Apple AirPort router (configured for NAT)
Locked IPT-box (using DHCP and NAT traversing)
-
...
2
votes
1answer
36 views
Route only ssh traffic through VPN
Is it possible to route a computer's SSH service through a VPN connection but allow ALL other data to exit through the WAN address? What sort of iptables magic needs to be done to accomplish this?
...
2
votes
1answer
144 views
PPTP server with NIC aliases
I have set up a VPN on a VPS Server using PPTP. I have one NIC with two aliases.
eth0
eth0:1
eth0:2
The 3 interfaces have public addresses. eth0 is a French IP, eth0:1 is UK, and eth0:2 is ...
2
votes
1answer
135 views
How do I ensure outbound TCP/IP traffic always uses a VPN, even when using Wifi?
I'd like to ensure that my VPN is started and running, before any TCP traffic from any of my background services send or receive data. How can I guarantee that this is the case?
How do I handle ...
2
votes
1answer
384 views
Multiple VPN connetions, routing based on country
I want to set up a couple of VPN connections to two different countries, A and B, on my Ubuntu Server. Then I would like to set up rules based on GeoIP to determine which VPN connection should be used ...
2
votes
3answers
275 views
VPN and gateway problems
I've got a corporate VPN, which I use to access the Internet. When it's on, I cannot reach the servers inside the corporate network anymore, so I think there are some problems with the gateway setup. ...
2
votes
1answer
2k views
How to connect to OpenVPN with NetworkManager
I have installed an OpenVPN server on my OpenWrt 10.03 router [freshly flashed]: https://pastebin.com/raw.php?i=hRECWuf1
echo "nameserver 8.8.8.8" > /etc/resolv.conf; opkg update; opkg install ...
2
votes
1answer
98 views
Incoming/Outgoing seperation for VPN
My situation is that I want all my outgoing connections from my Debian server to pass through a commercial VPN service I've subscribed to, but I still want to run public-accessible services on this ...
2
votes
1answer
422 views
Cannot load tun module
I cannot manage to load the tun module in my archlinux box. I'm trying
to connect with openvpn, but the log says
nm-openvpn[6662]: Note: Cannot open TUN/TAP dev /dev/net/tun: No such device ...
2
votes
1answer
714 views
Routing in OpenVPN between a private network and a client
I'm trying to setup OpenVPN between a private network and home clients that connect to it. (The clients don't need to connect to each other). The network topology is a little interesting. There is a ...
2
votes
1answer
857 views
L2TP IPsec VPN client configuration
I have Linux (Fedora) box and I want to conject to VPN described as "L2TP IPsec VPN" one. I have got following credentials:
user=xxxxxxxxx
pass=xxxxxxxxx
VPN server= XXX.XXX.XXX.XXX
IPsec ...
2
votes
0answers
56 views
How to bind ppp0 interface (PPTP VPN) as 'external' in proxy server?
I'm trying to bind ppp0 interface (PPTP VPN) as 'external' interface in proxy server (Tinyproxy). Unfortunately it does not work.
Using route add -net default gw 10.9.0.1 I can make all the traffic ...
2
votes
0answers
156 views
How to start racoon VPN IKE negotiation automatically?
I have configured racoon at two ends (with pre-shared keys) and trying to establish tunnel. But I have to initiate traffic to start IKE negotiation.
Is there any alternative to establishing the ...
2
votes
0answers
454 views
Smallest linux distribution for PPTP VPN server (poptop)?
I want to run Poptop, an Open Source PPTP Server for Linux.
I need the smallest possible GNU/Linux distribution which I can install in VMware Workstation 8 and which will be able to support this ...
2
votes
1answer
424 views
Setup PPTP VPN connection with no GUI [closed]
I want to configure a remote linux (Ubuntu Precise) to use a PPTP VPN. I can only access to it using ssh, so I don't have a graphical interface (neither do I want it).
Some hours googling:
Guides ...
2
votes
0answers
1k views
IPSec VPN Debian Squeeze Server for Mac OS X
I'm trying to get an IPSec VPN set up on my Debian home server, so that I can access my home network and browse without having my internet filtered by my college network, and so that I can perform ...
2
votes
0answers
991 views
Cisco AnyConnect on Fedora
I have downloaded the setup for Cisco AnyConnect client from our client's secure web URI. This setup script was for 32 bit machine while mine is a 64 bit one. However, I managed to install the client ...
2
votes
0answers
260 views
Route VPN gateway traffic via tun0 instead of normal gateway
On my Linux box, I have a tun0 interface by IPIP tunnel like:
tun0 Link encap:IPIP Tunnel HWaddr
inet addr:10.10.10.2 P-t-P:10.10.10.1 Mask:255.255.255.255
and I running an ...
1
vote
2answers
1k views
VPN like solution for SSH Tunneling?
Socksify like program for Fedora?
Socksify, tsocks, proxycommand in ssh, they're great softwares/solutions that can be used to "constrain" given apps to use a SOCKS5 proxy (what was created with an ...
1
vote
2answers
101 views
Encrypt IP payload + URL
I need to encrypt IP payload + request URL so that my ISP can't understand my requests. Do you know any project such as zebedee except VPNs?
Tor doesn't work with my ISP, because SSL was banned, so ...
1
vote
2answers
2k views
Configuring a VPN in my CentOS server
My server runs CentOS 6.2. It has two network cards (eth0 and eth1). In my server I have installed CoovaChilli access controller software, that manages the LAN under it. This management is done ...
1
vote
1answer
198 views
Hamachi for Web Surfing
I recently installed Hamachi on my FreeBSD 9 and I want to know how can I browse web anonymously by this software?
1
vote
1answer
104 views
VPN, one server, multiple clients
I wanted to know if it was possible to have a server running OpenVPN with server key and have multiple clients connect to it?
I would like the server to be 10.9.8.1, the first client to be 10.9.8.2 ...
1
vote
1answer
361 views
Only routing certain traffic through VPN
I have a central development server, running a VPN server, and a couple clients that need to connect to it. The server is running Apache, but is only accepting local requests (only listening on ...
1
vote
1answer
60 views
Should a VPN have access to all networks from and on all clients?
I have an OpenVPN server and many clients connecting. The VPN settings include
port 443
dev tun
proto tcp
When I add clients to my VPN I have to use apaches proxypass in order to access resources ...
1
vote
1answer
527 views
Ensure torrent client uses openvpn
I recently signed up to a VPN provider and to log in, I use network manager for my normal wireless connection and then start the openvpn connection from network manager.
In my browser I can check ...
1
vote
2answers
499 views
Change default DNS on openvpn connect
I am using Network Manager on Ubuntu 12.10 to connect to an openvpn server. The connection works without problems. However, when I connect, I would like to change my default DNS server to a server ...
1
vote
1answer
397 views
Kernel module for Cisco VPN client doesn't compile under ubuntu 10.04 LTS?
I am trying to install a Cisco VPN client under Ubuntu 10.04 LTS. In the extracted folder I type:
alex@alex-laptop:~/Downloads/cisco4.8/vpnclient$ sudo ./vpn_install
and there is output of activity ...
1
vote
1answer
2k views
“Linux kernel source code directory” requested in Cisco VPN client install
I'm trying to install Cisco's vpn client, and it requests that I provide the directory containing linux kernel source code. Specifically, it reads:
In order to build the VPN kernel module, you ...
1
vote
1answer
396 views
How to install/use sshuttle on Fedora?
How exactly can I install/use sshuttle under Fedora? It's not in the repositories
