1
vote
0answers
195 views

openswan l2tp/IPsec VPN server (NAT'ed)

I have searched for a solution for this problem for a few days now and cannot seem to find anything close to my situation (server is always NAT'd and clients are sometimes NAT'd). I am trying to ...
1
vote
0answers
112 views

IPsec Tunnel mode - RoadWarriors configuration

I've the need to configure IPsec tunnel mode between a gateway with static NAT (let's say its public IP is 172.31.0.105) and a number of clients that are behind dynamic NAT. Reading through some ...
4
votes
1answer
80 views

IPsec doesn't read configuration when the tunnel is deleted

I've created a tunnel between two sites using IPsec. I've made an error in the configuration, the address of the destination was false, so I deleted this tunnel. But after deleting, ipsec tries to ...
0
votes
0answers
198 views

death_handler: Fatal signal 15 received

I have problem with my Linux when I try to shut it down. init 0 I get the following error: death_handler: Fatal signal 15 received setsockopt recvref[30]: Protocol not available The sytem will ...
0
votes
1answer
73 views

Is VNC traffic bypassing IPSec and L2TP tunnel?

I have a CentOS 6.5 server running: a tightvnc server a StrongSwan to provide IPSec VPN xl2tpd to provide L2TP/IPSec VPN The VNC clients are: RealVNC Viewer on OSX Android-vnc-viewer on Android ...
4
votes
1answer
845 views

How to fix this eth0 and eth1, where traffic going out via eth0 is failing?

I have two public IPs. One's connected to eth0 and one to eth1, from 2 separate routers as complete DMZ towards the LAN IP. I added this following: ip rule add from 10.0.0.108/32 table 1 # outbound ...
2
votes
0answers
264 views

Openswan ipsec hub and spoke setup is not working

I have configured Hub and Spoke using openswan ipsec. Tunnel is immediately getting UP but the problem is: Spoke1 can ping/access HUB's LAN and vice-versa (S1 -- HUB && HUB -- S1) Spoke2 can ...
1
vote
0answers
2k views

Openswan established NATed tunnel but, I can't ping remote end's lan PC

I am establishing site to site tunnel. 192.168.2.0/24===10.103.6.40<10.103.6.40>---10.103.6.1...10.103.6.29<10.103.6.29>===192.168.1.0/24; Local ip: 10.103.6.40 Local lan: ...
8
votes
2answers
4k views

Openswan connecting to multiple right subnets not working

I'm trying to use Openswan (version 2.6.37) to connect an IPsec VPN from my local network to a remote site. Everything works fine when I just want to connect to a single subnet on the remote site. ...
2
votes
0answers
252 views

How to start racoon VPN IKE negotiation automatically?

I have configured racoon at two ends (with pre-shared keys) and trying to establish tunnel. But I have to initiate traffic to start IKE negotiation. Is there any alternative to establishing the ...
1
vote
0answers
473 views

Which of VPN or IPSec or xxx can I use here?

I'm renting a dedicated server which has a fixed / static IP and I'm using this server / IP for my business. I'm hosting a webapp / webappserver on it (Apache + Tomcat) and I've also set it up as a ...
2
votes
0answers
2k views

IPSec VPN Debian Squeeze Server for Mac OS X

I'm trying to get an IPSec VPN set up on my Debian home server, so that I can access my home network and browse without having my internet filtered by my college network, and so that I can perform ...
2
votes
0answers
397 views

Route VPN gateway traffic via tun0 instead of normal gateway

On my Linux box, I have a tun0 interface by IPIP tunnel like: tun0 Link encap:IPIP Tunnel HWaddr inet addr:10.10.10.2 P-t-P:10.10.10.1 Mask:255.255.255.255 and I running an ...
0
votes
2answers
2k views

Can't access internet after connecting to L2TP IPsec VPN

I have configured a L2TP VPN on Ubuntu server 11.04, and I can connect to it with a Mac client. But after connecting successfully to this L2TP VPN, my Mac cannot access the internet. To access the ...