I/O is an acronym for Input/Output, which refers to the mechanism or process for the transfer of information between one system or component and another.

learn more… | top users | synonyms

1
vote
2answers
67 views

dd command: Finding read/write throughput of a flash/SD?

I am running petalinux from sd card. And trying to find data copying rate from Sd card and from QSPI flash that is there on the Xilinx Zynq board. As suggested here , I am doing like this: ...
2
votes
1answer
45 views

How to customize or reprogram function of specific keys on my keyboard and the LED on my laptop

When I disable bluetooth on my laptop, the light does not go off and the blinking of the Wi-Fi LED is starting to bother me. Since I sometimes use my laptop in a poor lighting condition an illuminated ...
2
votes
1answer
60 views

Getting IO privileges in Linux

I have installed flashrom software. When i try to run sudo flashrom command it gives me "Could not get I/O privileges (Operation not permitted). You need to be root" error. Also I tried su command to ...
2
votes
1answer
143 views

CONFIG_GPIO_SYSFS makes /sys/class/leds disappear

I have an embedded Linux board I'm working on, with a button and a couple LEDs. By default, I can control the LEDs via /sys/class/leds/redled/brightness However, I have no way to monitor the ...
1
vote
1answer
80 views

Strange problem with IO or file system or what?

On a SLES 11 SP2 32-bit system I'm seeing a strange problem. It's as if the OS can not open a file from the beginning of the file. Say I have a file that is 200 lines. If I cat or more or vi the ...
1
vote
1answer
116 views

Determine how much a process is using each disk?

How do I tell how much load a particular process is contributing to each of several available volumes/mounts? It seems that dstat only shows aggregate stats across all processes per disk, and iotop ...
3
votes
0answers
85 views

Unable to close a Luks partition

For backup purposes, I have "snapshotted" a LVM partition. This partition was crypted so I have opened this Luks partition (snapshot) in order to do my backup. The problem is that I have forgotten to ...
2
votes
0answers
58 views

`crontab -e` sometimes fails with “Creation of temporary crontab file failed”

From time to time crontab -e fails on me on a Ubuntu box. It is the same for all users including the root and crontab -eu <user> under the root. Goes like this on a regular basis, a success here ...
2
votes
0answers
105 views

jbd2 journal constant i/o

iotop reports a constant i/o about 3% of [jbd2/vda1-8], I think this is the journal manager for ext4. my fstab is: UUID=X / ext4 defaults,noatime,nodiratime 1 1 tmpfs /dev/shm ...
2
votes
0answers
550 views

find ount what [flush-8:0] is writing

Using iotop, I found out that [flush-8:0] is doing a lot of hard disk activity, which explains the annoying slowdowns. However, I can't figure out what's the actual cause behind this flushing. No ...
2
votes
0answers
98 views

Shorter timeout on I/O errors MacOS X

How do you set a shorter timeout value for read/write I/O errors on MacOSX? We tend to get a few semicrashed disks and want to rsync the contents to a secure location, but when the file subsystem ...
2
votes
0answers
447 views

GNU/Linux, IO performance problems

I have some problems with my system performance. As I was adviced here, I used sar: $sar -u 5 and found out that the problems are caused by a low HDD performance, as I supposed (high %iowait). ...
1
vote
0answers
141 views

IOMMU causing freezes, disabling causes USB to not work

I'm somewhat new to linux, but I'm running a Xubuntu machine that I recently built. Since I started it up, I had noticed frequent freezes, where both the screen (if plugged in) and any SSH session ...
1
vote
0answers
139 views

How different is I/O handling of hard disk in AIX and Redhat Linux?

I am running a hadoop I/O workload in redhat linux and have ran that in IBM AIX as well with same underlying hardware, disk and disk configuration. With the default settings on the os redhat linux is ...
1
vote
0answers
1k views

How to set up ZFS with ZIL and L2ARC SSD?

I have been considering bcache and flashcache. However my friend suggested me something called ZFS. In fact it says that formating disk with ZFS can actually do the exact same thing without kernel ...
0
votes
0answers
24 views

Calculate Total disk i/o by a single process

I am looking for some tool that will dump total disk I/O by a single process after it ends. So far my finding is :- iotop= It shows i/o per process in real time but does not give total after process ...
0
votes
0answers
17 views

I2c with 16 bit addresses

So, i'm trying to interface with a device that has 16-bit addresses, and the master I'm using also supports this mode. However since this isn't standard I2C (should be 8-bit addresses) I haven't been ...
0
votes
0answers
76 views

Is swapping the cause of high IO on my box?

I'm running a LAMP stack on an Amazon EC2 micro instance with 616 MB of memory. This seems sufficient to be able to run a few small websites with Apache, MySQL and PHP. I have one Wordpress site ...