0
votes
2answers
61 views

Removing duplicated files in the rootfs - to speed up booting time, and improve memory usage

With Buildroot I'm making images for my Embedded Linux Hardware. Mainly I'm trying to speed up the boot sequence (and on the way lower the memory usage), where I've tried many techniques successfully. ...
0
votes
0answers
40 views

Can't access GPIOs when switching to systemd, but why?

I'm using this ARM AT91 Sam9x5ek Embedded Device, with my Linux Images made by a Buildroot. Usually my init-system is Busybox, now I changed it to systemd. Since then I can't access the GPIO anymore, ...
1
vote
0answers
223 views

Unable to add serialport (nodejs module) when generating filesystem and cross-compiling tools for an ARM processor

I am using buildroot (version 2013.08.1) to generate the filesystem and cross compiling tools to implement embedded linux on a i.MX233 processor (ARM architecture). I add the serialport module by ...
0
votes
1answer
165 views

How can I boot with a compressed rootfs?

My problem is: I cannot use compressed rootfs (the kernel crashes during boot) but uncompressed ones work fine. What I did: I'm using Buildroot 2013.11 to generate Images for my embedded Linux ...
1
vote
1answer
83 views

WARNING: at kernel/irq/handle.c - after changing rootfs, but why?

today I changed from an image with initramfs to an image with separate kernel and rootfs. Theses images are used for an Embedded System (ARM9 SAM9G25), that is runnging with an Linux 2.6.39. During ...
1
vote
0answers
86 views

Why is my embedded Linux unable to detect the sd device?

I have this ARM9 SAM9G25 embedded System, running a Linux 2.6.39 Kernel and a Busybox. I put the Images (of the bootloaders, and the linux+initramfs) on a SD so that in the end the system is booting ...
5
votes
1answer
278 views

How to set the CPU freq. in Linux?

I'm using this ARM9 SAM9G25 embedded system, that when switched on, is only online for a few seconds and because I want to speed up the whole process, I'd like to check the CPU frequency, and set it ...
3
votes
1answer
2k views

How to extract files from uImage?

Buildroot is generating Images for an embedded device where they should run on. This is working very well. In those Images the rootfs is included. Due to some research I'd like to look into that ...
0
votes
3answers
67 views

How can I add a script to embedded Linux

I have a script (let's say Hello World), that I want to include to my embedded Linux. I'm using Buildroot and want to start the script in Busybox. But because I'm cross-compiling for the target I'm ...
0
votes
1answer
146 views

Change the root filesystem on an embedded system

I'm using Buildroot to generate an embedded Linux with a kernel v. 2.6.39, which in the end starts busybox. Everything works fine when building with Initramfs as "rootfs". But Initramfs isn't the best ...
0
votes
0answers
101 views

how to enable java support to buildroot

I'm using buildroot 2012.08 version for building embedded linux. I'm looking for best solution to add java support. Is it possible to do trough buildroot?
0
votes
1answer
280 views

Unable to get embedded device to ping anything on the network

I have an embedded device, built using buildroot, kernel version 3.6.11 running busybox. The kernel is built with completely default options. I have configured the device according to what the network ...
3
votes
2answers
522 views

Adding Buildroot Package

I'm trying to add a package to buildroot, but I'm not having much success. The package I'm trying to add is an autotools package called scew. I've followed the buildroot guidelines about adding ...
0
votes
1answer
346 views

What happens with /etc/fstab when using an initramfs?

I have a simple embedded setup as follows: x86 target, kernel and root file system built using buildroot. Syslinux is the bootloader configured to boot with an initramfs which points to a .cpio file ...
2
votes
1answer
598 views

Does uClibc support using pthreads?

I recently attended an embedded Linux course that stated that uClibc does not support the use of pthreads and that it only supports linuxthreads. Furthermore, the course instructor implied that ...
0
votes
0answers
88 views

Colour is not working with ncurses on target embedded system built with buildroot

I have built an embedded linux environment for AMD Geode target. The kernel, cross toolchain and root file system were built using buildroot and the root file system resides on my host machine and is ...
10
votes
2answers
2k views

Is using a read only root file system a good idea for embedded setup?

I have been tasked with running Linux as an operating system on an embedded device. The target has an x86 processor and has 8 GB CompactFlash device for storage. I have managed to use buildroot to ...
2
votes
0answers
360 views

Error cross compiling linux kernel using buildroot

I am trying to build a kernel bt in cross compiling the kernel when I ran following command make CROSS_COMPILE=i686-linux- ARCH=x86 I got the following error: UCLIB_EXTRA_CFLAGS="" \ ...