I just know that
Interrupt is a
hardware signal assertion caused in a processor pin. But I would like to know how Linux OS handles it.
What all are the things that happen when an interrupt occurs?
Here's a high-level view of the low-level processing. I'm describing a simple typical architecture, real architectures can be more complex or differ in ways that don't matter at this level of detail.
When an interrupt occurs, the processor looks if interrupts are masked. If they are, nothing happens until they are unmasked. When interrupts become unmasked, if there are any pending interrupts, the processor picks one.
Then the processor executes the interrupt by branching to a particular address in memory. The code at that address is called the interrupt handler. When the processor branches there, it masks interrupts (so the interrupt handler has exclusive control) and saves the contents of some registers in some place (typically other registers).
The interrupt handler does what it must do, typically by communicating with the peripheral that triggered the interrupt to send or receive data. If the interrupt was raised by the timer, the handler might trigger the OS scheduler, to switch to a different thread. When the handler finishes executing, it executes a special return-from-interrupt instruction that restores the saved registers and unmasks interrupts.
The interrupt handler must run quickly, because it's preventing any other interrupt from running. In the Linux kernel, interrupt processing is divided in two parts:
Gilles already described the general case of an interrupt, the following applies specifically to Linux 2.6 on an Intel architecture (part of this is also based on Intel's specifications).
An interrupt is an event that changes the sequence of instructions executed by the processor.
Exceptions are caused by programming errors (f.e. Divide error, Page Fault, Overflow) that must be handled by the kernel. He sends a signal to the program and tries to recover from the error.
The following two exceptions are classified:
Interrupts can be issued by I/O devices (keyboard, network adapter, ..), interval timers and (on multiprocessor systems) other CPUs. When an interrupt occures, the CPU must stop his current instruction and execute the newly arrived interrupt. He needs to save the old interrupted process state to (probably) resume it after the interrupt is handled.
Handling interrupts is a sensitive task:
Two different interrupt levels are defined:
Every hardware device has it's own Interrupt Request (IRQ) line. The IRQs are numbered starting from 0. All IRQ lines are connected to a Programmable Interrupt Controller (PIC). The PIC listens on IRQs and assigns them to the CPU. It is also possible to disable a specific IRQ line.
The mid-step between an interrupt or exception and the handling of it is the Interrupt Descriptor Table (IDT). This table associates each interrupt or exception vector (a number) with a specified handler (f.e. Divide error gets handled by the function
Through the IDT, the kernel knows exactly how to handle the occurred interrupt or exception.
So, what does the kernel when an interrupt occurres?
First of all participants involved in interrupt handling are peripheral hardware devices, interrupt controller, CPU, operating system kernel and drivers. Peripheral hardware devices are responsible for interrupt generation. They assert interrupt request lines when they want attention from operating system kernel. These signals are multiplexed by interrupt controller, which is responsible for interrupt signals collection. It also responsible for determination of the order in which interrupt signals will be passed to CPU. Interrupt controller is able to temporally disable particular interrupt request line (IRQL) and reenable it again (IRQL masking). Interrupt controller pass collected interrupt requests to the CPU sequentially. CPU after completion of execution of each instruction CPU does check is there any waiting interrupt requests from the interrupt controller. If CPU finds that there is waiting request AND Interrupt Enable flag is set in the internal CPU control register then CPU starts interrupt handling. As you can see, by manipulation on the Interrupt flag in the CPU and communication with interrupt controller, Linux kernel is able to control the interrupt acceptance. For example, Linux can disable acceptance of interrupts from the particular device or disable interrupt acceptance at all.
What happens when the processor receives an interrupt request? Firstly, CPU automatically disables interrupts by resetting Interrupt Flag. They will be reenabled once interrupt handling will be finished. In the same time CPU makes minimal amount of work needed for switching CPU from the user mode to kernel mode in such a way that will allow it resume the execution of the interrupted code. CPU consults with special CPU control structures filled by Linux kernel to find an address of code to which control will be passed. This address is the address of the first instruction of interrupt handler, which is a part of the Linux kernel.
As a first step of interrupt handling kernel identifies vector of interrupt received to identify what kind of event has been happened in the system. Interrupt vector defines what actions will Linux take to handle it. As a second step Linux saves the rest of the CPU registers (which wasn't saved by CPU automatically) and which potentially can be used by the interrupted program. This is very important action, because it allows Linux to handle interrupts transparently regard to the interrupted program. As a third step, Linux accomplish switching to the kernel mode by setting the kernel environment and setting the CPU state required for it. And finally, vector dependent interrupt handler is called. (You can look on BUILD_INTERRUPT3 macro in arch\x86\kernel\entry_32.S to grab the additional details for x86 architecture related example) In the case of peripheral devices this a do_IRQ() routine. (Look into the arch\x86\kernel\irq.c)
The vector dependent interrupt handler usually wrapped by calls to irq_enter() and irq_exit(). Code area enclosed within a pair of these functions, is atomic with respect to any other such areas and also is atomic with respect to pairs of cli/sti. Irq_enter() and irq_exit() also captures some statistics related to the interrupt handling. Finally, kernel looks into the vector_irq table to find the irq number assigned to the vector of the interrupt received and call handle_irq() (from arch\x86\kernel\irq_32.c).
At this point the common part of the interrupt handling in Linux ends, because kernel looks the device dependent interrupt handler routine installed by device driver as part of the irq descriptor and invokes it. If such handler wasn't been installed by driver, kernel just acknowledge interrupt on interrupt controller and goes to exit from general interrupt handler.
After the end of the interrupt handling kernel restores the state of the program which was interrupted previously and resumes this program execution.
From theory aspect, almost everything has been explained. But if you are looking for explanation on kernel interrupt handling code framework, following link should you: A code walk inside kernel interrupt handling
And if you are still looking on theory about interrupts and interrupt handlers, then i recommend reading this: Understanding interrupts and interrupt handlers
http://tldp.org/LDP/tlk/dd/interrupts.html explains everything about the question u have asked