Take the 2-minute tour ×
Unix & Linux Stack Exchange is a question and answer site for users of Linux, FreeBSD and other Un*x-like operating systems.. It's 100% free, no registration required.

Followed this guide: https://wiki.archlinux.org/index.php/OpenVPN_Bridge

This is my setup: I have a wireless router(192.168.2.1) which connects to the Internet through a PPPoE connection and acts as a gateway and DHCP server for the local network. I'm trying to make a VPN on a machine(192.168.2.201).

I bridged the VPN tap0 with eth0 through br0 like in the guide. Connecting works ok and the client receives the proper IP but I cannot access other machines on the local network (ping works only server and client).

This is my server.conf:

port 1194
proto tcp
dev tap0
ca ca.crt
cert server.crt
key server.key  # This file should be kept secret
dh dh1024.pem
ifconfig-pool-persist ipp.txt
server-bridge 192.168.2.1 255.255.255.0 192.168.2.202 192.168.2.210
push "route 192.168.2.0 255.255.255.0"
keepalive 10 120
comp-lzo
persist-key
persist-tun
status openvpn-status.log
verb 6

This is my client.conf:

client
dev tap
proto tcp
remote hostname.com 1194
resolv-retry infinite
nobind
persist-key
persist-tun
ca ca.crt
cert client.crt
key client.key
ns-cert-type server
comp-lzo
verb 6

If you need any more info just ask. Thank you.

share|improve this question
add comment

2 Answers

Is the openvpn server a vmware virtual machine on a ESX/ESXi/VSphere server?

If yes, you may need to enable the promiscuous mode in the vmswitch.

The problem is that vmware ESX virtual switch will not "learn" new mac address by default, it just accept the VM mac address and nothing more.

In bridge mode the client TAP mac address is used in the openvpn server network and if the vmswitch is not setup correctly it will never work (tcpdump will show the ARP request, but no ARP reply for the vpn requests on the eth0 network. Until a tcpdump dont show the arp replies arriving for the vpn requests, the vmware vmswitch is still not correctly setup (on some setups, it's needed to setup the promiscuous to enable on two places)

switch the promiscuous mode by following this url

Finally, the openvpn bridge mode DO NOT require the ip_forward to be enable. a correctly setup bridge openvpn require a linux bridge (say br0) with the eth0 and tap0. BOTH are require to be in promiscuous mode (usually setup the eth0 on the machine network setup and the tap0 on the up.sh script). If setup like this, the vpn packages are simply bridge and the linux ip_forward is never called.

share|improve this answer
add comment
  • The server (the VPN endpoint) must act as a router to forward packets between the local and the VPN network - or rephrased: you got to enable IP forwarding on the server

  • Either the server announces himself as a router to the local network (if any routing protocol is active) or all clients have to be configured that the server is a gateway to the VPN network (best set up in a DHCP configuration if there is one)

share|improve this answer
    
Tried IP forwarding on a debian machine with the same setup. Ran iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE and iptables -A FORWARD -i br0 -j ACCEPT with no luck. IP forwarding is enabled.sysctl net.ipv4.ip_forward returns 1. –  laleshii Oct 21 '11 at 11:11
    
Also isn't the bridge I have created between eth0 and tap0 suppose to auto forward the packages between those 2 networks? –  laleshii Oct 21 '11 at 11:20
    
Before tampering with the server configuration (OpenVPN may have set up things already correctly for you) I'd check if the other network clients know, that to reach your system they have to use the server as gateway. A simple traceroute (from the other network client to your local VPN interface) would be the fastet solution to get an idea where things may need to be fixed. I suppose you can ssh to the server and from there ssh to an other network client. –  ktf Oct 21 '11 at 11:47
add comment

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.